ANSI/ASME B16.5 class 2500 weld neck flange
ANSI/ASME B16.5 standard covers pressure,temperature,ratings,materials,dimensions,tolerances,marking, testing,and methods of designating openings for pipe flanges and flanged fittings.Weld neck flange dimensions are covered in ANSI/ASME B16.5 for size NPS ½” to 12″ for above NPS 26″ to 60″ it should be as per ANSI/ASME B16.47.
ANSI/ASME B16.5 Class 2500 Weld Neck Flange Dimensions:
Pipe | Flange Data | Hub Data | Raised Face | Drilling Data | Weight | |||||||
Nominal Pipe Size
|
A | B | C | D | E | F | G | H | I | J | ||
Outside Diameter | Overall Diameter | Inside Diameter | Flange Thickness min | Overall Length | Diameter at Weld Bevel | Hub Diameter | Face Diameter | Number of Holes | Bolt Hole Diameter | Diameter of Circle of Holes | kg/piece | |
in mm |
in mm |
in mm |
in mm |
in mm |
in mm |
in mm |
in mm |
in mm |
in mm |
|||
½ | 0.840 21.30 | 5.250 133.4 | To be specified by purchaser | 1.190 30.20 | 2.880 73.15 | 0.840 21.30 | 1.690 42.90 | 1.380 35.00 | 4 | 0.880 22.40 | 3.500 88.90 | 3.12 |
¾ | 1.050 26.70 | 5.500 139.7 | 1.250 31.75 | 3.120 79.25 | 1.050 26.70 | 2.000 50.80 | 1.690 42.90 | 4 | 0.880 22.40 | 3.750 95.30 | 3.70 | |
1 | 1.315 33.40 | 6.250 158.8 | 1.380 35.10 | 3.500 88.90 | 1.320 33.50 | 2.250 57.15 | 2.000 50.80 | 4 | 1.000 25.40 | 4.250 108.0 | 5.24 | |
1¼ | 1.660 42.20 | 7.250 184.2 | 1.500 38.10 | 3.750 95.30 | 1.660 42.20 | 2.880 73.15 | 2.500 63.50 | 4 | 1.120 28.40 | 5.120 130.0 | 7.74 | |
1½ | 1.900 48.30 | 8.000 203.2 | 1.750 44.50 | 4.380 111.3 | 1.900 48.30 | 3.120 79.25 | 2.880 73.15 | 4 | 1.250 31.75 | 5.750 146.1 | 10.9 | |
2 | 2.375 60.30 | 9.250 235.0 | 2.000 50.80 | 5.000 127.0 | 2.380 60.45 | 3.750 95.30 | 3.620 91.90 | 8 | 1.120 28.40 | 6.750 171.5 | 16.2 | |
2½ | 2.875 73.00 | 10.50 266.7 | 2.250 57.15 | 5.620 142.7 | 2.880 73.15 | 4.500 114.3 | 4.120 104.6 | 8 | 1.250 31.75 | 7.750 196.9 | 23.7 | |
3 | 3.500 88.90 | 12.00 304.8 | 2.620 66.55 | 6.620 168.1 | 3.500 88.90 | 5.250 133.4 | 5.000 127.0 | 8 | 1.380 35.10 | 9.000 228.6 | 36.2 | |
4 | 4.500 114.3 | 14.00 355.6 | 3.000 76.20 | 7.500 190.5 | 4.500 114.3 | 6.500 165.1 | 6.190 157.2 | 8 | 1.620 41.10 | 10.75 273.1 | 55.3 | |
5 | 5.563 141.3 | 16.50 419.1 | 3.620 91.90 | 9.000 228.6 | 5.560 141.2 | 8.000 203.2 | 7.310 185.7 | 8 | 1.880 47.80 | 12.75 323.9 | 92.5 | |
6 | 6.625 168.3 | 19.00 482.6 | 4.250 108.0 | 10.75 273.1 | 6.630 168.4 | 9.250 235.0 | 8.500 215.9 | 8 | 2.120 53.80 | 14.50 368.3 | 143 | |
8 | 8.625 219.1 | 21.75 552.5 | 5.000 127.0 | 12.50 317.5 | 8.630 219.2 | 12.00 304.8 | 10.62 269.7 | 12 | 2.120 53.80 | 17.25 438.2 | 215 | |
10 | 10.75 273.0 | 26.50 673.1 | 6.500 165.1 | 16.50 419.1 | 10.75 273.0 | 14.75 374.7 | 12.75 323.8 | 12 | 2.620 66.55 | 21.25 539.8 | 406 | |
12 | 12.75 323.8 | 30.00 762.0 | 7.250 184.2 | 18.25 463.6 | 12.75 323.8 | 17.38 441.5 | 15.00 381.0 | 12 | 2.880 73.15 | 24.38 619.3 | 572 |
Notes:
- Dimension B corresponds to the pipe inside diameter. Values quoted assume 40S/Standard wall thickness.
- Weights are based on manufacturer’s data and are approximate.
Specifications of ANSI/ASME B16.5 flange:
Types of ANSI/ASME B16.5 forged flanges:
Weld neck flange(WN flange) is circumferentially welded into the system at its neck which means that the integrity of the butt welded area can be easily examined by radiography.The bores of both pipe and flange match,which reduces turbulence and erosion inside the pipeline.The weld neck is therefore favoured in critical applications. |
|
Blind flange is used to blank off pipelines,valves and pumps,it can also be used as an inspection cover.It is sometimes referred to as a blank flange. | |
Slip on flange(SO flange) is slipped over the pipe and then fillet welded.Slip-on flanges are easy to use in fabricated applications. | |
Lap joint flange(LJ flange) is always used with either a stub end or taft which is butt welded to the pipe with the flange loose behind it.This means the stub end or taft always makes the face.The lap joint is favoured in low pressure applications because it is easily assembled and aligned.To reduce cost these flanges can be supplied without a hub and/or in treated,coated carbon steel. |
|
Socket weld flange(SW flange) is counter bored to accept the pipe before being fillet welded.The bore of the pipe and flange are both the same therefore giving good flow characteristics. | |
Threaded flange is referred to as either threaded or screwed.It is used to connect other threaded components in low pressure, non-critical applications.No welding is required. | |
Ring type joint is a method of ensuring leak proof flange connection at high pressures.A metal ring is compressed into a hexagonal groove on the face of the flange to make the seal.This jointing method can be employed on weld neck flanges,slip on flange and blind flanges. |
Materials of ANSI/ASME B16.5 class 2500 weld neck flange:
Carbon steel ANSI/ASME B16.5 weld neck flange:
ASTM A105,A350 LF2,SS400,P235GH,P250GH,C22.8,Q235,20#,16Mn,etc.
Stainless steel ANSI/ASME B16.5 weld neck flange:
ASTM A182 F304,F304L,F316,F316L,F321,F347,F310,F44,F51,etc.
Alloy steel ANSI/ASME B16.5 weld neck flange:
ASTM A694 F42,F46,F52,F56,F60,F65,F70,A182 F5,F9,F91,F12,F11,F22,etc.
Related:
- ANSI/ASME B16.5 class 150 weld neck flange
- ANSI/ASME B16.5 class 300 weld neck flange
- ANSI/ASME B16.5 class 400 weld neck flange
- ANSI/ASME B16.5 class 600 weld neck flange
- ANSI/ASME B16.5 class 900 weld neck flange
- ANSI/ASME B16.5 class 1500 weld neck flange
- ANSI/ASME B16.5 class 2500 weld neck flange
Haihao Group is one of the the biggest flanges manufacturer & supplier & exporter in China,we has strong experience in flange production and inspection and a complete set of equipment,including advanced cutting,forging,machining,drilling machines and professional testing & inspection instruments.If you want to know more about our forged flanges,please email us:sales@haihaogroup.com